Toyota Camry manuals

Toyota
Toyota Camry
 Service Manual
Supplemental restraint system
Seat position air bag sensor (From July, 2003)

COMPONENTS

REPLACEMENT

REPLACEMENT

HINT: Installation is in the reverse order of removal.

  1. PRECAUTION

  2. DISCONNECT BATTERY NEGATIVE TERMINAL

  3. REMOVE FRONT SEAT ASSY LH

  4. REMOVE RECLINING POWER SEAT SWITCH KNOB (POWER SEAT)

  5. REMOVE SLIDE & VERTICAL POWER SEAT SWITCH KNOB (POWER SEAT)

  6. REMOVE FRONT SEAT CUSHION SHIELD INNER No.1 LH (POWER SEAT)

  7. REMOVE FRONT SEAT CUSHION SHIELD LH (POWER SEAT)

  8. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH (MANUAL SEAT)

  9. REMOVE VERTICAL SEAT ADJUSTER KNOB CAP (MANUAL SEAT)

  10. REMOVE VERTICAL SEAT ADJUSTER KNOB (MANUAL SEAT)

  11. REMOVE FRONT SEAT CUSHION SHIELD LH (MANUAL SEAT)

  12. REMOVE SEAT SLIDE POSITION SENSOR PROTECTOR

a. Remove the seat slide position sensor protector from the seat position airbag sensor.

13. REMOVE SEAT POSITION AIR BAG SENSOR

  1. Disconnect the connector from the seat position airbag sensor.

  2. Using a torx) socket wrench (T30), remove the torx) screw and the seat position airbag sensor.

14. INSTALL SEAT POSITION AIR BAG SENSOR

14. INSTALL SEAT POSITION AIR BAG SENSOR

  1. Check that the ignition switch is off.

  2. Check that the battery negative (−) terminal is disconnected.

CAUTION: After removing the terminal, wait for at least 90 seconds before starting the operation.

c. Using a feeler gauge 1 mm (0.039 in.), install the seat position airbag sensor.

NOTICE:

  • If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position airbag sensor with a new one.

  • When installing the seat position airbag sensor, be careful that the SRS wiring does not interfere with other parts and is not pinched between other parts.

HINT: Be sure to maintain a clearance between the seat position airbag sensor and the seat rail is within 0.6 mm (0.023 in.) to 2 mm (0.079 in.).

  1. Using a torx) socket wrench, tighten the torx) screw to install the seat position airbag sensor.

    Torque: 8.0 Nm (82 kgfcm, 71 in.Vlbf)

  2. Make sure that a clearance between the seat position airbag sensor and the seat rail is within 0.6 mm (0.023 in.) to 2 mm (0.079 in.).

  3. Connect the connector to the seat position airbag sensor.

  4. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  1. INSTALL FRONT SEAT ASSY LH

  2. INSPECT SRS WARNING LIGHT

    More about Supplemental restraint system:

    Horn button assy

    Spiral cable sub-assy

    Front passenger airbag assy (From July, 2003)

    Curtain shield air bag assy LH

    Front seat airbag assy RH

    Air bag sensor assy center

    Air bag front RH sensor

    Air bag sensor front LH

    Air bag sensor front LH

    Air bag sensor front LH

    Side air bag sensor assy RH

    Air bag sensor rear LH

    Seat position air bag sensor (From July, 2003)

    Occupant classification ecu (From July, 2003)

    Toyota Camry Service Manual / Supplemental restraint system / Seat position air bag sensor (From July, 2003)

    Toyota Camry Service Manual

    Categories


    2011-2017 Copyright www.tcamanual.com