Toyota Camry manuals

Toyota
Toyota Camry
 Service Manual
Supplemental restraint system
Spiral cable sub-assy

REPLACEMENT

HINT:

  • COMPONENTS

  • Installation is in the reverse order of removal.

  1. PRECAUTION

  2. DISCONNECT BATTERY NEGATIVE TERMINAL

CAUTION: After removing the terminal, wait for at least 90 seconds before starting the operation.

  1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  2. REMOVE STEERING WHEEL COVER LOWER No.2

  3. REMOVE STEERING WHEEL COVER LOWER No.3

  4. REMOVE HORN BUTTON ASSY

  5. REMOVE STEERING WHEEL ASSY

    SST 09950−50013 (09951−05010, 09952−05010, 09953−05020, 09954−05021)

  6. REMOVE STEERING COLUMN COVER (LOWER)

  7. REMOVE SPIRAL CABLE SUB−ASSY

  1. Raise the steering column cover (upper).

  2. Disconnect the connectors from the spiral cable sub− assy.

CAUTION: When handling the airbag connector, take care not to damage the airbag wire harness.

c. Disengage the 3 claws and remove the spiral cable sub− assy.

Remove spiral cable sub-assy Remove spiral cable sub-assy

  1. REMOVE STEERING SENSOR (W/ VSC)

  2. INSPECT SPIRAL CABLE SUB−ASSY

a. If any of the following conditions occur, replace the spiral cable sub−assy with a new one.

Condition: Scratches or cracks on the connector Cracks, dents or chipping of the spiral cable sub−assy

  1. INSTALL STEERING SENSOR (W/ VSC)

  2. INSTALL SPIRAL CABLE SUB−ASSY

  1. Check that the front wheels are facing straight ahead.

  2. Set the turn signal switch to the neutral position.

NOTICE: Make sure that the turn signal switch is in the neutral position, or the pin of the turn signal switch may be snapped.

c. Install the spiral cable sub−assy.

NOTICE: When replacing the spiral cable sub−assy with a new one, remove the lock pin before installing the steering wheel assy.

d. Connect the connector to the spiral cable sub−assy.

NOTICE: When handling the airbag connector, take care not to damage the airbag wire harness.

  1. INSTALL STEERING COLUMN COVER (LOWER)

  2. ADJUST SPIRAL CABLE SUB−ASSY

  1. Check that the ignition switch is off.

  2. Check that the battery negative (−) terminal is disconnected.

NOTICE: After removing the terminal, wait for at least 90 seconds before starting the operation.

c. Rotate the spiral cable sub−assy counterclockwise slowly by hand until it feels firm.

NOTICE: Do not turn the spiral cable sub−assy by the airbag wire harness.

d. Rotate the spiral cable sub−assy clockwise approximately

d. Rotate the spiral cable sub−assy clockwise approximately 2.5 turns to align the marks.

NOTICE: Do not turn the spiral cable sub−assy by the airbag wire harness.

HINT: The spiral cable sub−assy will rotate approximately 2.5 turns to both the left and right from the center.

  1. INSTALL STEERING WHEEL ASSY

  2. INSPECT STEERING WHEEL CENTER POINT

  3. INSTALL HORN BUTTON ASSY

  4. CONNECT BATTERY NEGATIVE TERMINAL

  5. INSPECT HORN BUTTON ASSY

  6. INSPECT SRS WARNING LIGHT

    More about Supplemental restraint system:

    Horn button assy

    Spiral cable sub-assy

    Front passenger airbag assy (From July, 2003)

    Curtain shield air bag assy LH

    Front seat airbag assy RH

    Air bag sensor assy center

    Air bag front RH sensor

    Air bag sensor front LH

    Air bag sensor front LH

    Air bag sensor front LH

    Side air bag sensor assy RH

    Air bag sensor rear LH

    Seat position air bag sensor (From July, 2003)

    Occupant classification ecu (From July, 2003)

    Toyota Camry Service Manual / Supplemental restraint system / Spiral cable sub-assy

    Toyota Camry Service Manual

    Categories


    2011-2017 Copyright www.tcamanual.com