Toyota Camry manuals

Toyota
Toyota Camry
 XV30 (2002–2006) Service Manual
Lighting
Fog lamp assy LH

OVERHAUL

HINT:

  • Use the same procedures for the RH side and LH side.
  • The procedures listed below are for the LH side.
  • Installation is in the reverse order of removal.
  1. REMOVE FRONT BUMPER ASSY

  2. REMOVE FOG LAMP ASSY LH

  1. Remove the 2 screws.
  2.  Move the fog lamp assy LH in the direction indicated by the arrow, disengage the hook, and remove the fog lamp assy LH.

Remove fog lamp assy LH Remove fog lamp assy LH

3. REMOVE FOG LAMP BULB

a. Turn the fog lamp bulb in the direction as shown in the illustration and remove the fog lamp bulb.

Remove fog lamp bulb Remove fog lamp bulb

  1. VEHICLE PREPARATION FOR FOG LAMP AIM ADJUSTMENT

  2. PREPARATION FOR FOG LAMP AIMING

  3. FOG LAMP AIMING INSPECTION

  4. FOG LAMP AIMING ADJUSTMENT

ADJUSTMENT

1. VEHICLE PREPARATION FOR FOG LAMP AIM ADJUSTMENT

a. Prepare the vehicle:

  • Ensure there is no damage or deformation to the body around the fog lamps.
  • Fill the fuel tank.
  • Make sure that the oil is filled to the specified level.
  • Make sure that the coolant is filled to the specified level.
  • Inflate the tires to the appropriate pressure.
  • Place the spare tire, tools, and jack in their original positions.
  • Unload the trunk.
  • Sit a person of average weight (68 kg, 150 lb) in the driver’s seat.

2. PREPARATION FOR FOG LAMP AIMING

a. Prepare the vehicle according to the following conditions:

  • Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lamps can be observed and above which it cannot.
  • Place the vehicle at a 90 angle to the wall.
  • Create a 7.62 m (25 ft) distance between the vehicle (fog lamp bulb center) and the wall.
  • Place the vehicle on a level surface.
  • Bounce the vehicle up and down to settle the suspension.

Preparation for fog lamp aiming Preparation for fog lamp aiming

NOTICE: A distance of 7.62 m (25 ft) between the vehicle (fog lamp bulb center) and the wall is necessary for proper aim adjustment.

If unavailable, secure a distance of exactly 3 m (9.84 ft) for check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.
  2. Draw a vertical line down the center of screen (V line).
  3. d. set the screen as shown in the illustration.

HINT:

  • Stand the screen perpendicular to the ground.
  • Align the V line on the screen with the center of the vehicle.

e. Draw base lines (H line, V LH, V RH lines) on the screen

e. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.

HINT: Mark the fog lamp bulb center marks on the screen. If the center mark cannot be observed on the fog lamp, use the center of the fog lamp bulb or the manufacturer’s name marked on the fog lamp as the center mark.

  1. H Line (Fog lamp height): Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog lamp bulb center marks of the low−beam fog lamps.
  2. V LH Line, V RH Line (Center mark position of left− hand (LH) and right−hand (RH) fog lamps): Draw two vertical lines so that they intersect the H line at each center mark.

3. FOG LAMP AIMING INSPECTION

3. FOG LAMP AIMING INSPECTION

  1. Cover or disconnect the connector of the fog lamp on the opposite side to prevent light from the fog lamp not being inspected from affecting fog lamp aiming inspection.
  2. Start the engine.

NOTICE: Engine rpm must be 1,500 or more.

c. Turn on the fog lamp and make sure that the cutoff line falls within the specified area, as shown in the illustration.

Fog lamp aiming inspection Fog lamp aiming inspection

4. FOG LAMP AIMING ADJUSTMENT

a. Adjust the fog lamp aim into the specified range by turning aiming screw with a screwdriver.

NOTICE: The final turn of the aiming screw should be made in the clockΩise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockΩise direction.

Fog lamp aiming adjustment Fog lamp aiming adjustment

    More about «Lighting»:

    Lighting system

    Headlamp assy LH

    Fog lamp assy LH

    Lighting system

    Rear combination lamp assy LH

    License plate lamp assy

    Center stop lamp assy

    Headlamp dimmer switch assy

    Lighting system

    Headlamp assy LH

    Toyota Camry XV30 (2002–2006) Service Manual / Lighting / Fog lamp assy LH

    Toyota Camry XV30 (2002–2006) Service Manual

    Categories


    © 2011-2024 Copyright www.tcamanual.com