Toyota Camry

 XV30 (2002–2006) Service Manual

Engine mechanical
Engine rear oil seal (1MZ−FE/3MZ−FE)

REPLACEMENT

1. REMOVE AUTOMATIC TRANSAXLE ASSY

2. REMOVE DRIVE PLATE & RING GEAR SUB−ASSY

a. Using SST, hold the crankshaft.

SST 09213−54015 (91651−60855), 09330−00021

b. Remove the 8 bolts, the rear spacer, the drive plate and the front spacer.

3. REMOVE ENGINE REAR OIL SEAL

1.  Using a knife, cut off the oil seal lip.

2. Using a screwdriver with its tip wrapped in tape, pry out the oil seal.

NOTICE: After the removal, check if the crankshaft is not damaged.

If it is damaged, smooth the surface with 400−grit sandpaper.

Remove engine rear oil seal

4. INSTALL ENGINE REAR OIL SEAL

a. Apply MP grease to a new oil seal lip.

NOTICE: Keep the lip off foreign materials.

b. Using SST and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.

SST 09223−15030, 09950−70010 (09951−07100)

NOTICE:

• Be careful not to tap the oil seal at an angle.

• Wipe off extra grease from the crankshaft.

 Install engine rear oil seal

5. INSTALL DRIVE PLATE & RING GEAR SUB−ASSY

1. Using SST, hold the crankshaft.

   SST 09213−54015 (91651−60855), 09330−00021

2. Clean the bolts and bolt holes.

3. Apply adhesive to 2 or 3 threads of the bolts.

   Adhesive:
   Part No. 08833−00070, THREE BOND 1324 or equivalent

4. Install the front spacer, the drive plate and the rear spacer on the crankshaft.

e. Uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

Torque: 83 N·m (846 kgf·cm, 61 ft·lbf)

NOTICE: Do not start the engine for at least an hour after installing.

6. INSTALL AUTOMATIC TRANSAXLE ASSY

Engine (2AZ−FE) (From July, 2003)

Timing gear case or timing chain case oil seal (2AZ−FE)(From July, 2003)

Engine rear oil seal (2AZ−FE)(From July, 2003)

Cylinder head assy (2AZ−FE) (From July, 2003)

Cylinder block assy (2AZ−FE)(From July, 2003)

Engine (1MZ−FE/3MZ−FE)

Drive belt (1MZ−FE/3MZ−FE)

Valve clearance (1MZ−FE/3MZ−FE)

Partial engine assy (1MZ−FE/3MZ−FE)

Partial engine assy (2AZ−FE)(From July, 2003)

Partial engine assy (1MZ−FE/3MZ−FE)

Timing belt (1MZ−FE/3MZ−FE)

Camshaft (RH BANK) (1MZ−FE/3MZ−FE)

Camshaft (LH BANK) (1MZ−FE/3MZ−FE)

Cylinder head gasket (1MZ−FE/3MZ−FE)

Cylinder head gasket No.2 (1MZ−FE/3MZ−FE)

Oil pump seal (1MZ−FE/3MZ−FE)

Engine rear oil seal (1MZ−FE/3MZ−FE)

Cylinder head assy (1MZ−FE/3MZ−FE)

Cylinder block assy (1MZ−FE/3MZ−FE)

Partial engine assy (2AZ−FE)(From July, 2003)

Drive belt (2AZ−FE)(From July, 2003)

Valve clearance (2AZ−FE)

Chain (2AZ−FE)(From July, 2003)

Camshaft (2AZ−FE)(From July, 2003)

Cylinder head gasket (2AZ−FE)(From July, 2003)